Hello,

The first 2 Webinars in the CADWorx P&ID Beginner Series have been posted to the CADWorx P&ID Training Section.

Upcoming Webinars are as follows:

[table  width=”95%” colwidth=”120|150|300|100″ colalign=”center|center|left|center”]

Date,Time,Topic,Registration Link

Aug 5,11:45 am – 12:15 pm,CADWorx P&ID Professional – Beginner Series 3 for P&ID – Attaching to a Database,Register
Aug 12,11:45 am – 12:15 pm,CADWorx P&ID Professional – Beginner Series 4 for P&ID – Drawing with a Database,Register
Aug 19,11:45 am – 12:15 pm,CADWorx P&ID Professional – Beginner Series 5 for P&ID – Loops and Reports,Register
Aug 26,11:45 am – 12:15 pm,CADWorx IP – Interoperability between CADWorx P&ID and CADWorx Plant,Register
[/table]

All,

Just a quick note to let everyone know that the last three ISOGEN Training Videos have been posted here.

• Isogen Training – The New I-Configure: Importing and Creating New Styles
• Isogen Training – The New I-Configure: The Drawing Setup Tool
• Isogen Training – The New I-Configure: The New “ECP”

Thank you

Jeffrey Suffet

CADWorx Plant Professional Training August 19-21

ECE is holding a specialized (3) day CADWorx Plant Professional training class in our Houston Training Center.

This custom class will consist of developing a skid using CADWorx Plant Professional 2014.  You will learn the basics of CADWorx Plant Professional including:

• Developing specifications
• Project Setup and Organization
• 3D Modeling
• Isometric Generation

Space is limited so sign up soon.  The cost is $1,500 for the 3 day session.  Classes will start at 8:30am and run until approximately 4:30.

Please contact us for more details on the training.

Thank you,

Gary Kohlbeck

All

We had a support call this morning on an installation issue.  CADWorx was installed on an Administrator account.  When the machine was switched over to the User Account, there was no Icon to run CADWorx.  When you install CADWorx from an Administrator account, a user will not have a profile setup automatically to run CADWorx.  In these cases, just go to the Start Menu and run the “Setup-Profile” command under the CADWorx Programs as shown below (while in the User Account):

 

Note: The CADWorx 2014 and CADWorx 2015 (Beta) locations are shown above.

Once the command is run, you can run CADWorx by using the newly created icons on the desktop.  

Note: Every once and a while the CADWorx Ribbons get ‘lost’ in AutoCAD.  Sometimes it has been working fine and all of a sudden you open AutoCAD and it fails to load the Ribbons.  I have even seen this happen when a new profile is created using the “Setup New Profile”.  In these cases, the Profile is created and loads but the partial customization files still don’t get loaded correctly.   In all cases, CADWorx is loaded and typing commands works fine but for some reason AutoCAD decides to ‘lose’ the connection to the partial customization files that hold the CADWorx Ribbons. To that end, we created a Specific On Topic (SPOT) Training Video on how to fix.   Please login to see the video HERE (Video 8: Missing CADWorx Ribbons).

Thank you,

Jeffrey Suffet

All,

The following is a list of newly posted CADWorx & Analysis Training Webinars:

[table  width=”95%” colwidth=”120|150″ colalign=”left|center”]

Topic,Link

CADWorx Plant – The Catalog: An Introduction,Link

CADWorx Plant – The Specifications: Long Description Formatting,Link

CADWorx Plant Isogen Training – The new I-Configure Series – Part 1,Link

[/table]

Below is a list of Upcoming CADWorx & Analysis Training Webinars:

[table  width=”95%” colwidth=”120|150|300|100″ colalign=”center|center|left|center|left”]

Date,Time,Topic,Registration Link

July 8 2014,11:45AM-12:15PM CST,Isogen Training – The new I-Configure Series Part 2,Register

July 15 2014,11:45AM-12:15PM CST,Isogen Training – The new I-Configure Series Part 3,Register

[/table]

Best Regards,

ECE Design